EVALUATION OF THE MARGINAL ACCURACY IN PORCELAIN FUSED TO METAL COPINGS FABRICATED IN TWO DIFFERENT FINISH LINES USING THREE DIFFERENT DIE MATERIALS -A STEREOMICROSCOPIC ANALYSIS AS A COMPARATIVE STUDY

SUBHA JOSHI *

Department of Prosthodontics, Crown and Bridge, School of Dental Sciences, Krishna Institute of Medical Sciences, Deemed to be University, Karad, India.

SHIV SAGAR TEWARI

Department of Prosthodontics, Crown and Bridge, School of Dental Sciences, Krishna Institute of Medical Sciences, Deemed to be University, Karad, India.

DR.PRIYA LAXMAN VASWANI

Department of Prosthodontics, Crown and Bridge, School of Dental Sciences, Krishna Institute of Medical Sciences, Deemed to be University, Karad, India.

*Author to whom correspondence should be addressed.


Abstract

Introduction: In the 20th century itself innovative techniques and materials were introduced for the fabrication of restorations that accurately fit over the prepared surface of the tooth. To fabricate these restorations, various materials like metals, alloys, resins, and ceramics were used. Regarding the different materials, metals and alloys have the advantage of superior strength, but for color, it is esthetically not acceptable. Due to a lack of esthetic value metals are replaced by ceramics.

Objective: To compare the effect of two different marginal geometries shoulder and deep chamfer on metal-ceramic copings fabricated with the use of three different die materials Conventional Type IV Gypsum, epoxy resin, resin-modified Gypsum (Synthetic Gypsum).

Methods: Two ivorine mandibular first molars were prepared using diamond points for receiving Full veneer porcelain fused to metal restorations. The two designs of circumferential finish evaluated in this study were shoulder and deep chamfer.

Results: Tests specimen fabricated on 3 groups of die material each having shoulder and deep chamfer finish line were analyzed under a stereomicroscope at four points, following results of vertical marginal gaps in μm were recorded.

Conclusion: It is thus concluded from the above study that dies fabricated using three different materials in two different finish lines i.e shoulder and deep chamfer did not exhibit a statistically significant difference in terms of marginal accuracy and either of these finish lines can opt for fabrication of metal-ceramic restorations.

Keywords: Alloys, ceramics, innovative techniques, metals, porcelain, resins


How to Cite

JOSHI, S., TEWARI, S. S., & VASWANI, D. L. (2021). EVALUATION OF THE MARGINAL ACCURACY IN PORCELAIN FUSED TO METAL COPINGS FABRICATED IN TWO DIFFERENT FINISH LINES USING THREE DIFFERENT DIE MATERIALS -A STEREOMICROSCOPIC ANALYSIS AS A COMPARATIVE STUDY. UTTAR PRADESH JOURNAL OF ZOOLOGY, 42(24), 1448–1452. https://doi.org/10.56557/upjoz/2021/v42i243284

Downloads

Download data is not yet available.

References

Martinsen BD. Marginal integrity of glass ionomer and all ceramic restorations. Uniformed Services University of the Health Sciences Bethesda United States; 2016.

Mejía JB, Wakabayashi K, Nakamura T, Yatani H. Influence of abutment tooth geometry on the accuracy of conventional and digital methods of obtaining dental impressions. The Journal of prosthetic dentistry. 2017;118(3):392-9.

Logozzo S, Zanetti EM, Franceschini G, Kilpelä A, Mäkynen A. Recent advances in dental optics–Part I: 3D intraoral scanners for restorative dentistry. Optics and Lasers in Engineering. 2014;54:203-21.

McLean JW. The science and art of dental ceramics-volume I: The nature of dental ceramics and their clinical use. Quintessenz Verlag; 2019.

Kocaağaoğlu H, Kılınç Hİ, Albayrak H, Kara M. In vitro evaluation of marginal, axial, and occlusal discrepancies in metal ceramic restorations produced with new technologies. The Journal of prosthetic dentistry. 2016; 116(3):368-74.

Stone PO. of Dental Sciences. Indian Journal of Dental Sciences; 2014.

Zimmermann M, Egli G, Zaruba M, Mehl A. Influence of material thickness on fractural strength of CAD/CAM fabricated ceramic crowns. Dental materials journal. 2017; 2016-96.

Jhavar S, Paul CP, Jain NK. Causes of failure and repairing options for dies and molds: A review. Engineering Failure Analysis. 2013; 34:519-35.

Nassar U, Oko A, Adeeb S, El-Rich M, Flores-Mir C. An In vitro study on the dimensional stability of a vinyl polyether silicone impression material over a prolonged storage period. The Journal of prosthetic dentistry. 2013;109(3):172-8.

Lillywhite GR, Vohra F. Influence of polyurethane resin dies on the fit and adaptation of full veneer crowns. Indian Journal of Dental Research. 2015;26(1):72.

Brecker SC. Porcelain baked to gold— A new medium in prosthodontics. The Journal of prosthetic dentistry. 1956;6(6):801-10.

Mondelli J, Ishikiriama A, Galan Jr J. Marginal microleakage in cemented complete crowns. The Journal of Prosthetic Dentistry. 1978; 40(6):632-6.

Bergenholtz G, Cox CF, Loesche WJ, Syed SA. Bacterial leakage around dental restorations: its effect on the dental pulp. Journal of Oral Pathology & Medicine. 1982; 11(6):439-50.

Omar. R SEM study of unveneered and veneered ceramic restorations J. Prosthet Dent. 1987;21:528.

Singh V, Gupta S, Bhargava A, Kaul S. Marginal accuracy of metal copings produced with different ring casting techniques: An In vitro study. European Journal of Prosthodontics. 2015;3(2):36.

Gujjarlapudi MC, Reddy SV, Madineni PK, Ealla KK, Nunna VN, Manne SD. Comparative evaluation of few physical properties of epoxy resin, resin-modified gypsum and conventional type IV gypsum die materials: an in vitro study. J Contemp Dent Pract. 2012;13(1):48-54.